Home page

Products

FPC P0.50 50P SMT flip top type

This operation specification is suitable for: 0.5 PITCH FPC CONN. ZIF R/A SMT clamshell type Connection with FPC/FFC: ZIF; FPC/FFC suitable thickness: 0.30±0.05mm

Key words:

Classification:

FPC Series

Online message

Detail description

1 Scope of application

This operation specification is suitable for: 0.5 PITCH FPC CONN. ZIF R/A SMT clamshell type

Connection with FPC/FFC: ZIF;

FPC/FFC suitable thickness: 0.30±0.05mm

2 Associated Specifications

EIA-364 : Test Procedures for Electronic Connectors and Connectors

UL STD-94 : Specifications for testing the flame retardancy of plastic equipment parts and equipment

3 Construction Dimensions Material

See construction drawing Materials

parts

Suppliers of raw materials

Material name/Type name

FLAME CLASS

FILE NO.

main body

(HOUSING)

Polyplastics

POLYPLASTICS CO., LTD

LCP

Liquid crystal polymer

473i (natural color)

V-0

E106764

putter

(ACTUATOR)

Kuraray

KURARAY CO., LTD

PA9T

Polyamide 9T

GP2450 (Black)

V-0

E90350

4 standard status

4.1 Rated voltage: AC/DC 50V

4.2 Rated current: 0.5A

4.3 Temperature and humidity range

4.3.1 Operating temperature range: -40~85℃;

4.3.2 Storage temperature range: -40~85℃;

4.3.3 Storage humidity range: relative humidity below 90%RH.

5 performance

5.1 Structure

serial number	project	Test Methods	Specifications
1	Exterior	Visual inspection, inch measurement.	Meet the drawing requirements

5.2 Electrical properties

serial number	project	Test Methods	Specifications
1	contact resistance	Test on the same terminal, current: 1.0A (DC), voltage: below 5V, use wire: adapt to FFC standard wire.	30mΩ Max.
2	Insulation resistance	DC 500V between adjacent terminals, 1 minute.	500MΩ Min.
3	Pressure test	AC 500V between adjacent terminals, induction current 2mA, 1 minute.	No breakdown, no short circuit.
4	The temperature rises	When the terminal is working at rated voltage and current, measure the temperature rise of the terminal.	30℃ Max.

5.3 Mechanical properties

	project	Test Methods	Specifications
1	FFC/FPC holding force	After the FFC is inserted into the FPC connector, it is pulled out vertically at a constant speed of 25~100mm/min. After this action is repeated three times, the measurement data is recorded for the fourth time.	20gf/pin
2	Terminal retention	Pull out the terminal vertically from the rubber core groove at a constant speed of 25~100mm/min	100gf/terminal Min.
3	Flip action force (No leather wire after high temperature)	FFC (leather wire) is not inserted into the main body, and the pressing force of the flip cover and the pulling force of the flip cover are measured. After this action is repeated three times, the measurement data is recorded for the fourth time.	Flip cover pressing force 500gf Max. Pull out force of flip cover 40gf Min.
3	Flip action force (High temperature after-installation leather thread)	Insert the FFC line into the main body, press the cover and pull it up. This action is repeated three times, and the measurement data is recorded for the fourth time.	Flip cover pressing force 1500g/f Max. Pull out force of flip cover 150g/f Min.
4	Plug Durability	Do the following moves for 30 rounds: FPC insertion, SLIDER insertion, SLIDER extraction, FPC extraction	Contact resistance 50mΩ Max . Terminals are free from deformation and cracks

5.4 Durability

serial number	project	Test Methods	Specifications
1	Vibration resistance	The terminals are connected in series with a current of 0.1A DC, an amplitude of 1.5mm, a frequency of 10-55-10Hz, and X, Y, and Z directions for 2 hours each, for a total of 6 hours.	Contact resistance 50mΩ Max. Discontinuous conduction within 1μs; no abnormal appearance.
2	Impact resistance	The terminals are connected in series with a current of 0.1A DC, the acceleration is 490m/s ² , the X, Y, and Z directions are 11ms each, 3 times each, 18 times in total.
3	cold resistance	Place at -25±3°C for 48H.	1 Contact resistance: 50mΩ Max. 2 Insulation resistance: 500 MΩ Min. 3 withstand voltage: no breakdown, short circuit 4 Appearance: no abnormality
4	heat resistance	Place it at a temperature of 85±2°C for 96 hours.
5	Moisture resistance	The temperature is 40±3℃; the storage time is 96H in the humidity of 90~95% RH.
6	Salt spray test	Temperature 35±2℃; Salt water specific gravity 5±1% Spray test: A: Gold plating 48h B: Tin plating 16h C: Single pin terminal 48h
7	Thermal shock	-55±3°C; 85±2°C for 30 minutes each, for a total of 5 cycles.
8	Moisture resistance (Temperature and humidity cycle	Follow the curve below to complete the 5 cycle test.
9	Tin Wetting	Dipping tin temperature 245±3℃ (Sn: Lead Free); time 3±0.5s	eat tin full, Above 95%.
10	Solder heat resistance	Soldering iron temperature 350±10℃ (Sn: Lead Free); time 10+1/-0s.	meet the electrical performance, Appearance is normal, Tin foot and fixed piece are flat Roundness 0.10mm Max.
11	Reflow heat resistance	Preparatory heating time: 150°C 60~120s. Soldering temperature time: 250℃ 30±1s.
12	Sulfur resistance (gold-plated product)	According to the technical standard SS-00126-12 three kinds of mixed GAS corrosion test.	Contact resistance: 50mΩ Max. No visible corrosion near contacts.
13	Solvent resistant	Place product in isopropyl alcohol container for 90 seconds and remove.	meet the electrical performance, Appearance is normal.

6 packs

see bundle diagram

Operating Instructions and Precautions

1): FFC insertion method: open and close the flip cover, please implement it when the connector is installed on the circuit board; push the flip cover up to unlock it, pull it up with your index finger and thumbnail, you can easily Simple operation.

2): When inserting the FFC, please do it with the cover fully open, the conductor of the FFC faces down, and the FPC is inserted vertically relative to the connector. Make sure that the FFC is inserted to the bottom of the body. This product is structurally designed , the flip cover cannot be opened more than 100°, so do not apply force beyond this range on the rear, otherwise the flip cover will loosen or be damaged.

3): Press down on the middle part of the flip cover, and when the FFC is inserted halfway, or if the insertion misalignment is extremely large, the flip cover will not be locked well and will float. At this time, take out the FFC according to the method of 4), and start the operation from 1) again. At the same time, when performing locking operations, the connector must be fixed.

4): The method of pulling out the FFC; open the flip cover according to the method in 1; when pulling out the FFC, please do it with the flip cover fully open. In case the flip cover is not fully opened, pull out the FFC , When reinstalling the FFC, please confirm whether there is any attachment on the contact part.

5): For FFC, please do not apply pulling force on it, or apply prying force in the direction of its terminal spacing.

6): Please avoid operations such as pinching or pulling out the cover with your fingers (especially pulling it out with your fingernails)

7): Please insert the FFC into the connector's insertion port correctly. Make sure that the FFC is inserted to the bottom of the body. If it is inserted incorrectly, it will cause a short circuit and poor conduction. When inserting the FFC, do not rub the connector hard Otherwise, the terminal will collide strongly with the FFC, resulting in deformation of the terminal and peeling of the FFC conductor.

8): If it is a large PIN number, please press the two ends of the cover to close it.

Pre

FPC P0.5mm R/A SMT UPPER CONTACT 10P

FPC P2.50mm SMT NON-ZIF 3P

Pre

FPC P2.50mm SMT NON-ZIF 3P